Runco VX-40d Manuel d'utilisateur Page 65
- Page / 108
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Installation
Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual 53
PRE
L
IMINAR
Y
• Color Enable: Select which color or colors you want to see in the display. This is
useful while working with color temperature white levels or input levels.
When you have finished calibrating Input 1, change the Display Device Input Source to DVI
(Input 2) if that input will be used; refer to
Selecting the Input Source on page 36. Then,
repeat the procedure described in this section (starting with Channel Setup) for Input 2.
After calibrating projector Input 2, proceed with the next section, Working With the
Lamp.
3.14
Working With the
Lamp
Access the Lamp menu to:
• Choose a lamp mode for regulating power and light output.
• Change the optical aperture size.
• View information pertaining to past and present lamps.
• Record the lamp serial number in the projector’s memory.
Lamp Hours (read-only): Lamp Hours shows the number of hours logged on the
current lamp. Whenever you record a new lamp serial number, the
VX-40d/-50d/-60d/-80d automatically resets this value to “0” and begins to log time for
the new lamp.
Lamp S/N (read-only): Lamp S/N is the serial number recorded for the current lamp.
When you install a new lamp and enter its serial number, the number appears here.
Lamp Message: Enter a check mark for Lamp Message to enable a warning message
that appears upon power-up when the lamp has reached the specified lamp limit and
should be replaced. Delete the check mark to prevent display of this message—instead,
when your lamp expires, only the status display messages on the back of the projector will
provide a visual warning to replace the lamp.
Lamp Limit: Set Lamp Limit to the number of hours you expect to log on the current
lamp before replacing it. This will trigger a lamp message on-screen (if enabled).
1. It is recommended that the Lamp Message check box remain
enabled.
2. When a lamp warning message appears, press EXIT to
temporarily cancel the message. The message will continue to
appear upon power-up until you install a new lamp.
1. If you change modes over the life of a lamp, the lamp limit you
originally expected may no longer be possible.
2. Turning the lamp on and off reduces lamp life significantly, as do
other factors.
3. It is recommended that Lamp Limit not exceed the expected
lamp life, otherwise a lamp could become dangerously fragile
with overuse.
Note
Note
- VX-40d / VX-50d 1
- VX-60d / VX-80d 1
- TWO YEAR LIMITED WARRANTY 3
- Safety Precautions 6
- Table of Contents 10
- List of Figures 11
- 1. Introduction 13
- Using This Manual 14
- Description, Features 15
- Introduction 16
- 2. Controls and Functions 17
- 1 7 863 5 92 4 18
- Controls and Functions 19
- -80d Rear-Panel 20
- DHD Controller Front 22
- DHD Controller Rear 23
- Remote Control 25
- 3. Installation 29
- Quick Setup 30
- Installation 31
- Considerations 31
- Estimating Throw Distance 32
- Ceiling Installation 34
- Floor Installation 34
- Installing the 37
- Projection Lens 37
- Installing the Optional 38
- CineWide Lens Mount 38
- AutoScope stand used 39
- Mounting the 40
- DTV or Progressive 43
- Component (YPbPr) 43
- Personal Computer 44
- Red Green Blue Horiz Vert 44
- DVD Player, VCR 45
- Satellite Receiver 45
- Laser Disc etc 45
- Control System 46
- Component SD NTSC 480i 48
- Anamorphic VX-40/50 DVI 48
- Installing and 50
- Adjusting the 50
- CineWide Anamorphic 50
- Too Far Right 51
- Too Far Left 51
- Correct position 51
- Too High 52
- Correct Lens Angle 52
- Incorrect Lens Angle 52
- Wrong Position 53
- Correct Position 53
- Calibrating Projector 54
- 01 0,1 p5W 48.73k+ 60.01+ 57
- 02 0,2 pDig DVI out fm DHD 57
- 03 0,1 i5W 33.72k- 60.00 57
- No Resizing 60
- Working With the 65
- 4. Operation 69
- Operation 70
- Active Image 72
- Area (4:3) 72
- 2.35:1 Image on 73
- 16:9 Screen 73
- Below Black 74
- Vertical Keystone Correction 83
- Positive values 83
- Negative values 83
- Lamp and Filter 85
- Replacement 85
- Front Filter Access Cover 87
- Side Filter Access Cover 87
- Lens Replacement 88
- Troubleshooting Tips 89
- Table 6-1. Serial Commands 95
- Serial Communications 100
- 7. Specifications 101
- DHD Controller 104
- Specifications 104
- VX-40d/-50d/-60d/ 105
- -80d Dimensions 105
- SERIAL NUMBER 108
Produits connexes et manuels pour Projecteurs Runco VX-40d
(2 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.938 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels