Runco VX-40d Manuel d'utilisateur Page 60
- Page / 108
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Installation
48 Runco VX-40d/-50d/-60d/-80d Owner’s Operating Manual
PRE
L
IMINAR
Y
Size and Position Menu In the Size and Position Menu, you can increase or decrease the size of your image,
change its proportion (aspect ratio), move the image to a specific area of the screen, and
refine other related parameters. Use Size and Position controls to match the image
precisely to the screen. Changes made in the Size and Position menu take effect
immediately and are saved when you exit the menu.
Resize Presets: Select a Resize Presets option to quickly display an image in its native
resolution or to automatically resize an image to closely fill the projector’s native resolution,
or to optimize the display width or height.
The native resolution is model-dependent, as follows:
• VX-40d or VX-50d: 1280 x 720 (16:9 native aspect ratio)
• VX-60d or VX-80d, 788p models: 1400 x 788 (16:9 native aspect ratio)
• VX-60d or VX-80d, 1050p models: 1400 x 1050 (4:3 native aspect ratio)
Size, Position and Blanking parameters automatically adjust accordingly. If Blanking is set
first, which defines an Active Input Area, Resize Preset scaling occurs in this region of
interest only.
For use with the DHD Controller, the default setting is No Resizing. This is almost always
the appropriate setting. Do not change it unless specifically instructed to do so by Runco
Technical Support.
• No Resizing: Select No Resizing to display the image in its native resolution, which
may or may not match the projector’s resolution. For example, for a computer display
with a native resolution of 800 x 600, “No Resizing” will use the central 800 x 600 pixels
and have a black border— the black border areas are unused areas.
Figure 3-18. Resize Presets: No Resizing
➤
The “native” aspect ratio is with the primary lens only. With an
anamorphic lens in the light path, the aspect ratio is 16:9 with the
VX-60d and VX-80d (1050p models), and 2.35:1 with all other
models.
Note
1280
720
788
1050
VX-40d/
VX-50d
SVGA 800x600
Model
Source Type
VX-60d/
VX-80d
(788p)
VX-60d/
VX-80d
(1050p)
1400
1400
1280
720
788
1050
NTSC
1400
1400
1280
720
788
1050
HDTV 720p
1400
1400
HDTV 1080i
No Resizing
Active Image Area
Unused Pixels
788
1050
1400
1400
1280
720
- VX-40d / VX-50d 1
- VX-60d / VX-80d 1
- TWO YEAR LIMITED WARRANTY 3
- Safety Precautions 6
- Table of Contents 10
- List of Figures 11
- 1. Introduction 13
- Using This Manual 14
- Description, Features 15
- Introduction 16
- 2. Controls and Functions 17
- 1 7 863 5 92 4 18
- Controls and Functions 19
- -80d Rear-Panel 20
- DHD Controller Front 22
- DHD Controller Rear 23
- Remote Control 25
- 3. Installation 29
- Quick Setup 30
- Installation 31
- Considerations 31
- Estimating Throw Distance 32
- Ceiling Installation 34
- Floor Installation 34
- Installing the 37
- Projection Lens 37
- Installing the Optional 38
- CineWide Lens Mount 38
- AutoScope stand used 39
- Mounting the 40
- DTV or Progressive 43
- Component (YPbPr) 43
- Personal Computer 44
- Red Green Blue Horiz Vert 44
- DVD Player, VCR 45
- Satellite Receiver 45
- Laser Disc etc 45
- Control System 46
- Component SD NTSC 480i 48
- Anamorphic VX-40/50 DVI 48
- Installing and 50
- Adjusting the 50
- CineWide Anamorphic 50
- Too Far Right 51
- Too Far Left 51
- Correct position 51
- Too High 52
- Correct Lens Angle 52
- Incorrect Lens Angle 52
- Wrong Position 53
- Correct Position 53
- Calibrating Projector 54
- 01 0,1 p5W 48.73k+ 60.01+ 57
- 02 0,2 pDig DVI out fm DHD 57
- 03 0,1 i5W 33.72k- 60.00 57
- No Resizing 60
- Working With the 65
- 4. Operation 69
- Operation 70
- Active Image 72
- Area (4:3) 72
- 2.35:1 Image on 73
- 16:9 Screen 73
- Below Black 74
- Vertical Keystone Correction 83
- Positive values 83
- Negative values 83
- Lamp and Filter 85
- Replacement 85
- Front Filter Access Cover 87
- Side Filter Access Cover 87
- Lens Replacement 88
- Troubleshooting Tips 89
- Table 6-1. Serial Commands 95
- Serial Communications 100
- 7. Specifications 101
- DHD Controller 104
- Specifications 104
- VX-40d/-50d/-60d/ 105
- -80d Dimensions 105
- SERIAL NUMBER 108
Produits connexes et manuels pour Projecteurs Runco VX-40d
(2 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.634 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels