Runco VX-2000d Manuel d'utilisateur Page 61
- Page / 88
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Operation
Runco VX-2000d Owner’s Operating Manual 49
PRE
L
IMINAR
Y
• Runco/ISF Logo Splash Screen Timers: When you turn on the VX-2000d, it
projects a welcome screen with the Runco logo followed by one with the ISF logo.
Select Splash Timer from the
Splash Configure menu to set the amount of time that
these two images appear. The range is from 2 to 60 seconds, in one-second
increments.
Use the up or down cursor button to select a timer value to adjust. Use the right or left
cursor button to change the timer value. Press MENU when you have finished
configuring both timers.
OSD Position: Select OSD Position, press ENTER and use the arrow buttons to change
the size and position of the OSD controls.
ServiceUse the Service menu to access advanced projector configuration settings. This menu
should be used by ISF-certified technicians only.
Test Video: Select Test Video from the Service Menu to access the internal test patterns
on the VX-2000d. Four patterns are available, consisting of white/gray or colored bars.
Press MENU to exit test pattern mode.
Input Names: You can give each DHD Controller input a descriptive name. For example,
you may want to change the default input name to the type of source component
connected to it: “VCR,” “DVD,” “Laptop” et cetera. Composite, S-Video and Component
SD input names can be up to 12 characters long; the others can be up to eight characters
long.
To edit an input name, select Input Names from the Service menu. Press or to select
an input and press ENTER. Use the or buttons to change a character; press or
to select a character to change. When you have finished editing the input name, press
MENU.
To restore the default input name, press repeatedly to highlight that input name in the
“Restore” column. Then, press ENTER.
To save input names so that they can be restored after a System Reset (described on
page 52), press repeatedly to highlight “Save.” Then, press ENTER.
Service
Test Video
Input Names
Remote Control
Analog Out Mode
Display Device
HD Format
Triggers
Miscellaneous
Resolution
System Reset
Restore Saved Settings
You must enter a passcode to access the Service menu.
Note
Input Names
Restore
Composite Composite
S-Video 1 S-Video 1
S-Video 2 S-Video 2
Component SD Component SD
HD/RGB 1 HD/RGB 1
HD/RGB 2 HD/RGB 2
HDMI 1 HDMI 1
HDMI 2 HDMI 2
Save
The button takes you from top to bottom in the left column, then
from top to bottom in the right column. To highlight “Save,” scroll
through both columns.
Note
- VX-2000d 1
- TWO YEAR LIMITED WARRANTY 3
- Safety Precautions 6
- Table of Contents 10
- List of Figures 11
- 1. Introduction 13
- Using This Manual 14
- Description, Features 15
- Introduction 16
- 2. Controls and Functions 17
- Controls and Functions 18
- VX-2000d Rear Panel 19
- DHD Controller Front 20
- DHD Controller Rear 22
- VX-2000d Remote 24
- Control Unit 24
- VX-2000d Built-In 27
- 7m/23ft 29
- Installation 30
- Quick Setup 31
- Considerations 32
- Estimating Throw Distance 33
- Screen width (w) 33
- Ceiling Installation 34
- Floor Installation 34
- Mounting the 36
- Connections to the 37
- VX-2000d and DHD 37
- Controller 37
- HDMI Source 38
- (HD-DVD/BD/DVD Player or 38
- HD Tuner with 38
- HDMI or DVI out) 38
- DTV or Progressive 39
- Component (YPbPr) 39
- Personal Computer 40
- Red Green Blue Horiz Vert 40
- DVD Player, VCR 41
- Satellite Receiver 41
- Laser Disc etc 41
- Control System 42
- Current Source Format 44
- Resolution 44
- Aspect Ratio 44
- Primary Lens 45
- Adjustments 45
- Installing and 46
- Adjusting the 46
- CineWide Anamorphic 46
- Too High 47
- Correct position 47
- 4. Operation 49
- Chroma Delay 50
- 4:3 Image, stretched to fill 52
- 16:9 Screen (Display) 52
- 16:9 Image on 52
- 2.35:1 Image on 53
- 16:9 Screen 53
- Below Black 54
- the White Balance sub-menu 59
- Operation 60
- On-Screen Menus for 64
- 1080i (Digital) or 64
- 1080p Signals 64
- Green Offset 65
- Default Yes/No 65
- Overscan + 66
- English 67
- Deutsch 67
- Español 67
- Français 67
- Italiano 67
- Sources (continued) 68
- ICC Adjust 69
- HD/RGB Adj 71
- THESE SCREWS 73
- Troubleshooting Tips 74
- Table 6-1. Serial Commands 77
- 7. Specifications 83
- DHD Controller 85
- Specifications 85
- VX-2000d Dimensions 86
- RUMA-009330 88
- SERIAL NUMBER 88
Produits connexes et manuels pour Projecteurs Runco VX-2000d
(2 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.652 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels