Runco REFLECTION Spécifications Page 66
- Page / 92
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Operation
54 Runco RS-1100 Series Owner’s Operating Manual
PRE
L
IMINAR
Y
RS-232 Baud Rate: Press the or button to select the projector’s RS-232 Baud
Rate. This function is used to change the transfer rate of the RS-232 connection. (This
setting must match the data rate of the device connected to the RS-232 input.)
Blue Image: Press the or button to turn the Blue Image Off or On. This feature
removes all red and green color information from the image (simulating a blue filter), and is
useful for color-calibrating the projector or other video components.
Option To access the Option adjustments, press MENU, then press the or button to
highlight Option and press ENTER. The Installation sub-menu will then appear (see
above). Press EXIT to return to the previous menu or press MENU to close all menus.
Reset Image Settings: To restore the default image settings for the current input source
ONLY, press the
button to highlight “Yes,” then press ENTER.
Sleep Timer: The Sleep Timer automatically puts the projector into standby mode after
the amount of time you specify here. (A warning appears on-screen one minute before this
is to occur.)
Use the or button to set the timer for anywhere from 10 minutes to 3 hours, in
10-minute increments. To disable the Sleep Timer, set it to 0.
Lamp Hours: To find out how long the projector lamp has been in use, select Lamp
Hours and press ENTER.
OSD Timer: Use the or button to set the OSD Timer. This timer controls how long
the menus remain on-screen after selecting them. Select from 0 to 60 seconds, in
3-second increments. When you set the OSD to 0, the menus remain on-screen until you
hide them by pressing MENU.
To adjust the horizontal and vertical position of the OSD, select OSD Position and press
ENTER. Then, press the
or button to select Horizontal or Vertical and use the
or button to adjust.
PC & HD Adjust: Use the settings in the PC & HD Adjust menu to fine-tune 480p and
higher-resolution signals for optimum picture quality.
•Auto: Adjusts the phase, frequency and position automatically.
•Freq. Adjusts the frequency of the signal.
•Phase: Adjust the phase if the image (usually from an RGB source) shows shimmer or
“noise.” Pixel phase adjusts the phase of the pixel sampling clock relative to the
incoming signal. The effect of this control is similar to that of a tracking control on a
VCR.
For best results, use a good test pattern such as a smooth gray consisting of a clear
pattern of black and white pixels, or a similar “half on, half off” graphic image. (You may
find that you can stabilize the image at more than one point. Use either setting in this
case.)
• H. Pos.: Adjusts the horizontal position of the image.
• V. Pos.: Adjusts the vertical position of the image.
Option
Reset Image Settings
Sleep Timer
Lamp Hours
OSD Timer
OSD Position
PC & HD Adjust
PIP/PBP Set Up
DNR
➤
To adjust the image position with a 480i source, use the Image
Shift controls in the Set Up menu (see page 59).
Note
Downloaded From projector-manual.com Runco Manuals
- RS-1100 Series 1
- TWO YEAR LIMITED WARRANTY 3
- Safety Precautions 6
- Table of Contents 10
- List of Figures 11
- Introduction 13
- Using This Manual 14
- Related Documents 14
- Description, Features 15
- 2. Controls and Functions 17
- Controls and Functions 18
- RS-1100 Rear Panel 19
- RS-1100 Remote 21
- Installation 25
- Quick Setup 26
- Considerations 27
- Ceiling Installation 30
- Floor Installation 30
- Installing the Optional 33
- CineWide/AutoScope 33
- Lens Motor (RS-1100 33
- Ultra only) 33
- Ceiling Mount 35
- Extension Brackets 35
- Mounting the RS-1100 36
- Connections to the 37
- DTV Source 40
- DVD Player, VCR 40
- Satellite Receiver 40
- D-Sub 9-pin female 41
- RJ-11 Male 41
- RJ-11 to 41
- D-Sub 9-pin Adapter 41
- (not included) 41
- Turning on the Power 43
- Installing and 45
- Adjusting the 45
- CineWide Anamorphic 45
- Too Far Right 47
- Too Far Left 47
- Correct position 47
- Too High 48
- Correct Lens Angle 48
- Incorrect Lens Angle 48
- Anamorphic Lens (Top View) 49
- 7 Pitch Adjustment 52
- Yoke for Lens 52
- 8 Lens 52
- Adapter Ring 52
- 9 Anamorphic Lens 52
- Operation 55
- Store Custom 1 57
- (see above) 57
- Below Black 59
- Active Image 64
- Area (4:3) 64
- 2.35:1 Image on 65
- 16:9 Screen 65
- )V( EGNAR TUPNI 69
- Remote Control 73
- Secondary 20 73
- Lamp Replacement 77
- Troubleshooting Tips 78
- Serial Communications 81
- Specifications 85
- RS-1100 Dimensions 88
- RS-1100 Ultra 89
- Dimensions 89
- RUMA-011215 92
- SERIAL NUMBER 92
Produits connexes et manuels pour Projecteurs de données Runco REFLECTION
(126 pages)Faure CGC406W manuals
Owner’s manuals and user’s guides for Unknown Faure CGC406W.
We providing 2 pdf manuals Faure CGC406W for download free by document types: User Manual
Table of contents
Table of contents
More products and manuals for Unknown Faure
| Models | Document Type |
|---|---|
| FRB29SD |
User Manual
Faure FRB29SD Manuel utilisateur,
14 pages
|
| CEC6062W |
User Manual
Faure CEC6062W Manuel utilisateur [de] [fr] ,
24 pages
|
| LFV1060 |
User Manual
Faure LFV1060 Manuel utilisateur,
24 pages
|
| CGC6901X |
User Manual
Faure CGC6901W Manuel utilisateur [lv] ,
28 pages
|
| FEE6940FXA |
User Manual
Faure FEE6940FXA Manuel utilisateur [sv] ,
12 pages
|
| CML517W |
User Manual
Faure CML517W Manuel utilisateur [it] [ru] [sk] ,
28 pages
|
| FCI5520CSA |
User Manual
Faure FCI5520CWA Manuel utilisateur [sk] ,
24 pages
|
| FCM5400CWA |
User Manual
Faure FCM5400CWA Manuel utilisateur,
28 pages
|
| FCH218W | User Manual Faure FCH218W Εγχειρίδιο χρήστη, 4 pages |
| FFU20200WA |
User Manual
Faure FFU20200WA Manuel utilisateur,
16 pages
|
| FCM5400CWA |
User Manual
Faure FCM5400CWA Manuel utilisateur,
24 pages
|
| FCM6500CSA |
User Manual
Faure FCM6500CWA Manuel utilisateur,
28 pages
|
| FGN68468BA |
User Manual
Faure FGN68468BA Manuel utilisateur,
28 pages
|
| FOP27001XK |
User Manual
Faure FOP27001WK Manuel utilisateur,
24 pages
|
| FCM660MWC |
User Manual
Faure FCM660MWC Manuel utilisateur,
28 pages
|
| FCM6500CSA |
User Manual
Faure FCM6500CSA Manuel utilisateur [pt] ,
28 pages
|
| FCG5103CXA |
User Manual
Faure FCG5103CXA Manuel utilisateur,
28 pages
|
| CMPI631S |
User Manual
Faure CMPI631S Manuel utilisateur,
28 pages
|
| F6203IOK |
User Manual
Faure F6203IOK Manuel utilisateur [it] ,
20 pages
|
| FCM6401CSA |
User Manual
Faure FCM6401CSA Manuel utilisateur,
24 pages
|
© 2020, manymanuals.fr. Tous droits réservés | 0.064 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels