OW N E R ’S OP E R A T I N G MA N U A LCL-410DLP™ Projector
10Projector (Rear and Side View)IntroductionAC socketInput: 100 - 240V3.5A, 50/60HzComponent 1 InputInputs for componentYPbPr / YCbCr.RS-232 terminalC
11Source ButtonsPress this button to select Composite video source.Press this button to select Component 1 source.Press this button to select RGB HD s
12Using the Remote ControlIntroductionAvailable Range of the Remote ControlThe remote control can be used to control the projector within the ranges s
13Before Setting UpConnections and SetupThis projector can be connected to:Video Equipment: VCR, Laser disc player or other video equipment with a Co
14Connection and SetupConnecting to Video EquipmentConnecting with S-Video or Composite Video CableYou can connect devices equipped with Composite vid
15Connection and SetupConnecting to DVI Video EquipmentYou can connect to devices equipped with DVI output, such as a DVD player or DTV decoder to the
16Connecting the Projector to a ComputerConnecting with HD15-pin VGA cable.1 Connect an HD 15-pin VGA cable to the RGB HD input on the projector. Se
17Connection and SetupConnecting the projector to a computer with DVI-D cable1 Connect a DVI-D cable to the DVI / Computer input on the projector. S
18Using the Adjustment FeetThe height of the projector can be adjusted using the adjustment feet. This is useful for correcting the angle of the proje
191 Zoom is adjusted by rotating the zoom ring.2 Focus is adjusted by moving the focus ring right or left until focus is achieve
2Table of ContentsLimited Warranty ... 3Preface ...
20The height and width of the projected image can be adjusted to be within the shift range of the lens by rotating the lens shift dial at the top of t
21Connection and SetupNote: • The projector lens should be centered on the screen. If the horizontal line passing through the lens center is not pe
22Connection and SetupWhen using a wide screen (16:9)When displaying a 16:9 picture on the whole area of the 16:9 screen.Throw Distance ChartCL-410 @
23When you project from behind the screen (rear projection), using a mirror, or from a ceiling mount, you need to reverse the image so that the image
24Ceiling-mount setup It is recommended you use the optional ceiling-mount bracket for this installation. Before mounting the projector, contact you
25Basic OperationBasic ProcedureConnect the required external equipment to the projector before completing the following procedures. The display langu
26Basic Operation1 Press one of the source buttons on the remote control, such as VIDEO, to select an input source, or move through input sources
27Using MenusBasic OperationThis projector has a set of menu screens that enable you to adjust the image and various projector settings. You can opera
28Basic Operation1, 2, 3, 4, 5Menu Items
29Basic Operation1, 2, 3, 4, 5
3TWO YEAR LIMITED WARRANTYFor Projectors, Video Processors and ControllersCongratulations on your purchase of a Runco video product and welcome
30Basic OperationPicture AdjustBrightness 64 ~ +64 (not available for DVI)Contrast 64 ~ +64
31Basic OperationIn the Picture Adjust menu, you can adjust Brightness, Contrast, Color, and other settings to control the appearance of projected ima
32Basic OperationColor Temperature ➤Color Space ➤White Balance ➤Save Settings ➤Restore Picture Settings ➤Use this option to set the color temperature
33Easy-to-Use FunctionsThis function enables you to modify or customize the aspect ratio. The aspect ratio refers to the picture display mode and the
34Table 1: Descriptions of six aspect ratio settings Anamorphic Standard Letterbox• Resolution
35Easy-to-Use FunctionsTable 2: Resolution (in pixels)InputVideo Equipment StandardAnamorphic Standard (4 × 3) Letterbox4:3 Aspect Ratio480i, 480P 576
36Easy-to-Use Functions
37Easy-to-Use Functions
38Easy-to-Use FunctionsThe Picture Adjust and Aspect settings enable you to adjust the size and position of the projected image. In the Image Option m
39Easy-to-Use FunctionsThis function enables you to adjust the horizontal and vertical position of the display.1 Select Image Position from the Imag
4Runco limits its obligations under any implied warranties under state laws to a period not to exceed the warranty period. There are no express warran
40Easy-to-Use FunctionsBrightness Enhance adds additional brightness to the display. Set to ON to enable.Brightness Enhance OptionsONOFFThe Lamp Power
41Easy-to-Use FunctionsInstallationThe Installation menu enables you to adjust source detection and the language and appearance of settings menus, key
42Easy-to-Use FunctionsThis function allows you to set the transparency of the OSD menu. When set to transparent, you can see the image behind the men
43Easy-to-Use FunctionsBlue Enable turns off the red and green colors so that only blue appears. Settings menus also appear bluish.Blue Enable Options
44Easy-to-Use FunctionsWhen the image is projected either from top or from bottom toward the screen at an angle, the image becomes distorted in a trap
45AppendixCleaning the Projector Unplug the power cord before cleaning the projector. Avoid using benzene or thinner, as these can damage the fini
46Appendix: MaintenanceThis projector is equipped with ventilation holes to ensure optimal operating temperature. Periodically clean the ventila
47Appendix: MaintenanceThe projector lamp has a life of 2000 hours. Maintain proper ventilation to keep the lamp operating throughout its lifetime. Do
481 If the projector is running, press OFF on the remote control to turn off the power. Wait until the cooling fan stops.2 Disconnect the power co
49Appendix: Connecting Pin AssignmentsConnecting Pin AssignmentsWhen the projector is used with a computer, the following features are supported:• Mul
5ADDITIONAL INFORMATION:To locate the name and address of the nearest Runco Authorized Service Center, or for additional information about this Limite
50Appendix: Connecting Pin AssignmentsNote: • This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD) mo
51Appendix: Compatibility Chart = Supported AR = Adjustment RequiredCompatibility ChartComponent 1/2 support signal formats are Y/Pb/Pr, Y/Cb/Cr
52Appendix: RS-232 InformationRS-232Pin Configuration: Pin 2: TxD Pin 3: RxD Pin 5: GroundCommunication: Baud Rate: 9600 Bits: 8 Parity: None S
53Appendix: TroubleshootingTroubleshootingIf the projector does not appear to be operating properly, note the symptoms present and use the following g
54Appendix: SpecificationsSpecificationsProjector Type:Digital Light Processing™ (DLP™), Single-Chip DMD™Native Resolution:1024 x 576Aspect Ratios:4:3
55Lamp:250W NSHLamp Life:2000 hoursInputs:(1) Composite Video, (1) S-Video, (2) RCA Component Video, (1) DVI w/HDCP, (1) VGA, (1) RS-232Power Requirem
56Appendix: DimensionsDimensions3.425 in87.0 mm3.425 in87.0 mm13.98 in355.0 mm8.276 in210.2 mm5.701 in144.8 mm6.457 in164.0 mm0.8976 in22.8 mm7.354 in
Runco International • 2900 Faber Street • Union City, CA 94587 • Ph (510) 324-7777 / (800) 23RUNCO / Fax (510) 324-9300www.runco.comRUMA-011100rev 7-1
ABOUT THIS MANUALThis manual is designed for use with the CL-410 Projector. Information in this document has been carefully checked for accuracy; howe
7WARNING! To meet FCC requirements, a shielded power cord is required in order to prevent interference. It is essential that only the supplied power c
8IntroductionWith the Reflection CL-410, Runco brings its famous video performance to a new level of affordability, putting Runco quality within reach
9IntroductionProjector (Front and Top View)Focus ring Adjusts focusLens shift dial (Horizontal)Shifts image right and leftTemperature indicatorIndica
Commentaires sur ces manuels